Welcome to The Australian Hayabusa Club Forum - ARCHIVE ONLY VERSION - NEW REGISTRATIONS & POSTS DISABLED › Bike Discussions › Technical Discussion v
Uneven wear...

Uneven wear...
BUSGO
Guest
 
#19
10-03-2006, 07:31am
Hey Anggi,
Just to be sure, check that both your front forks are evenly setup. A little more or less preload or compression damping on one side will also cause your front tyre to wear on one side more than the other.

Rgds BUSGO

"TAKE MY ADVICE"
I'm not using it anyway!<i></i>
Reply


Messages In This Thread
Uneven wear... - by chunkylover - 04-03-2006, 10:38pm
RE: Uneven wear... - by Bill Gaheer - 11-11-2007, 06:41pm
RE: Uneven wear... - by kawasuki - 11-11-2007, 06:47pm
RE: Uneven wear... - by Madmax - 11-11-2007, 07:22pm
RE: Uneven wear... - by Bill Gaheer - 12-11-2007, 08:23am
RE: Uneven wear... - by Madmax - 12-11-2007, 12:55pm
RE: Uneven wear... - by LOAFIE - 11-11-2007, 06:48pm
RE: Uneven wear... - by Bill Gaheer - 13-11-2007, 11:35am
Re: Uneven wear... - by simmo - 04-03-2006, 10:44pm
> Re: Uneven wear... - by Fat Busa Racing 1347 - 04-03-2006, 11:25pm
Re: > Re: Uneven wear... - by AstroBusa - 04-03-2006, 11:29pm
Spoil sport ! - by Sumkhun - 04-03-2006, 11:41pm
Methinks - by Sumkhun - 04-03-2006, 11:42pm
Re: Methinks - by AstroBusa - 04-03-2006, 11:51pm
Re: Methinks - by Sumkhun - 04-03-2006, 11:53pm
Re: Methinks - by AstroBusa - 04-03-2006, 11:54pm
Re: Methinks - by chunkylover - 05-03-2006, 09:53am
Re: Methinks - by baz - 05-03-2006, 10:31am
Re: > Re: Uneven wear... - by Blackkat - 05-03-2006, 12:22pm
Re: > Re: Uneven wear... - by AstroBusa - 05-03-2006, 01:34pm
Re: > Re: Uneven wear... - by rev 01 - 05-03-2006, 09:33pm
Re: > Re: Uneven wear... - by chunkylover - 06-03-2006, 07:37pm
Re: > Re: Uneven wear... - by kawasuki - 06-03-2006, 09:19pm
Re: > Re: Uneven wear... - by simmo - 07-03-2006, 09:53pm
Re: > Re: Uneven wear... - by chunkylover - 09-03-2006, 09:06pm
Re: > Re: Uneven wear... - by BUSGO - 10-03-2006, 07:31am
Re: > Re: Uneven wear... - by chunkylover - 10-03-2006, 04:53pm
Re: > Re: Uneven wear... - by chunkylover - 10-03-2006, 09:57pm
Re: > Re: Uneven wear... - by Blackzook - 11-03-2006, 02:56pm
Re: > Re: Uneven wear... - by chunkylover - 13-03-2006, 12:59pm



Users browsing this thread: 2 Guest(s)