04-03-2012, 06:30pm
so I'm getting thew itch for a 1441 cc engine build in my Gen II Busa. I'm not interested in bulding myself, so who do I see and how much would it cost to build and tune a tough streetable 1441??
I want a 1441 cc
|
04-03-2012, 06:30pm
so I'm getting thew itch for a 1441 cc engine build in my Gen II Busa. I'm not interested in bulding myself, so who do I see and how much would it cost to build and tune a tough streetable 1441??
05-03-2012, 07:37am
just about everything you could want to know would be in this thread, which is Bruce's 1441 build (blackzook)
http://www.australian-hayabusa-club.com/...1441+build
05-03-2012, 07:42am
05-03-2012, 08:38am
cheers for the quick replys guys!
05-03-2012, 07:46pm
Howdy Grizzly,
Out of curiosity seeing you are a very welcome P-plater on the forum and nothing wrong with new members asking questions why do you want to go the 1441? Is 1340 not quick enough with suspension mods/ pipes/ lower gearing and a flashtune? I would do these first...., like I did then think again of any more engine upgrades.
Hi Jamdonut, I have done all the usual mods Yoshi full system (soon to be swaped for a Brocks alienhead), flash tune using ECUeditor even have a 40 shot of gas on it for a bit of fun, looking at doing the Brocks ultra clutch inn the near future. I may be a P plater on here but have 10 years riding experence behind me and most of that on Busa's. The reason for the 1441 is, yes, I am a little bored and I do enjoy modding my toys.
06-03-2012, 04:51pm
totally off topic.... but what is good gearing for more fun on the busa? currently im running stock gears and its a little boring...
Ideas? (06-03-2012, 04:51pm)RyanG Wrote: totally off topic.... but what is good gearing for more fun on the busa? currently im running stock gears and its a little boring... Go up a couple at the rear ![]() (06-03-2012, 08:28am)Grizzly Wrote: Hi Jamdonut, I have done all the usual mods Yoshi full system (soon to be swaped for a Brocks alienhead), flash tune using ECUeditor even have a 40 shot of gas on it for a bit of fun, looking at doing the Brocks ultra clutch inn the near future. I may be a P plater on here but have 10 years riding experence behind me and most of that on Busa's. The reason for the 1441 is, yes, I am a little bored and I do enjoy modding my toys. Yeah but who wants a wheel standing machine out of every corner ![]() ![]()
07-03-2012, 12:38am
07-03-2012, 01:28am
(07-03-2012, 12:38am)bazman Wrote:(06-03-2012, 06:00pm)simmo Wrote: Yeah but who wants a wheel standing machine out of every corner You don't need a wheel standing machine Bazman ,You are one . If Wisdom Comes with Age , I'm one of the Smartest Blokes Here
07-03-2012, 06:52pm
10-03-2012, 06:24pm
(06-03-2012, 04:51pm)RyanG Wrote: totally off topic.... but what is good gearing for more fun on the busa? currently im running stock gears and its a little boring... 40 is stock for the rear of a gen 1. I run a 43. Will lift in 2nd, but not unless you're trying. ![]() I don't want a pickle . . .
15-03-2012, 01:41am
![]() Carrillo H-Beam stroker rods and spacer plate. #BSK1300-8.5OS 8.5 stroker with offset journals. Schnitz 0007-00001 Big Block, Billet, Suzuki Hayabusa - Muzzys $2,640.05 Bung ya head in a box & send to Competition CNC http://www.competitioncnc.com/busa.html#stage3 BUSA STAGE 3 O/S Valves $800 CNC Porting $260 Bronze Valve Guides $475 Bronze O/S Seats $350 O/S Stainless Valves $300 Valve Job $715 Cams $120 Springs $220 TI Retainers $60 Resurface $35 Valve Seals $120 Shim Cams $3,455 1661cc ---- should be good for the road. Gearbox Tool steel shift shafts. Low ratio 1st Hi Ratio 5th n 6th. Heavy duty output shaft. Think of the fuel economy; Up 1 tooth on front 530 sprocket. Down 2 teeth on rear 530 sprocket. 1441 ----- a dinky !!!! You'll need a good engine builder. Not a 5 minute job. You'll be right as you've got a PM off multicultural 1300dinky. Streetable, worried about your engine builder's competence ? APE'll do a 5mm (68mm) stroker crank with offset journals for 1580cc with the Muzzys Big Block. ![]() ![]()
15-03-2012, 10:40am
I just got a PM
![]() My sincere apologies have been sent. It will be worth while to have a 2nd motor so you can ride ya bike while its being built. ![]() |
« Next Oldest | Next Newest »
|