Contact Us
nope actually steps
1)remove tank
2)do i have to disconnect anything?fuel lines?any tricks to this?
3)is the filter in the tank or outside? etc
cheers
[/quote]
1 drain fuel from tank
2 remove seat
3 lift tank disconnect fuel line and fuel sender pump wires
4 lower tank unbolt n remove tank from bike,only undo the 2x 12mill bolts to the frame ,leave the 4x 10 mil bolts alone
5 place tank on soft surface upside down ,getallen key undo bolts holding in fuel pump
6 lift sender pump assembly from tank being careful not to bend fuel float
7 remove fitler from pump assembly 8 spray with carby cleaner ,then use compressed air the blow backwards back flush etc while doing this wrap white cloth around fitler as shit will go everywere
8 follow steps in reverse to re-assemble
good luck
[/quote]
REMOVED THE FUEL Filter from tank today, the whole goddamn unit is sealed.could nt see any friggin teabag filter.
so ended up pulling of a plastic cap that has a jet like fitting to enable fuel to go into the pump,poured injector cleaner into filter outlet and flushing it in reverse so compressed air came out of pump inlet-voila whining noise gone. maybe next 35k kms no issues if not new fuel pump assemble is the way to go i recon ,its too much dicking about opening the assembly i guess.
nope actually steps
1)remove tank
2)do i have to disconnect anything?fuel lines?any tricks to this?
3)is the filter in the tank or outside? etc
cheers
[/quote]
1 drain fuel from tank
2 remove seat
3 lift tank disconnect fuel line and fuel sender pump wires
4 lower tank unbolt n remove tank from bike,only undo the 2x 12mill bolts to the frame ,leave the 4x 10 mil bolts alone
5 place tank on soft surface upside down ,getallen key undo bolts holding in fuel pump
6 lift sender pump assembly from tank being careful not to bend fuel float
7 remove fitler from pump assembly 8 spray with carby cleaner ,then use compressed air the blow backwards back flush etc while doing this wrap white cloth around fitler as shit will go everywere
8 follow steps in reverse to re-assemble
good luck
[/quote]
REMOVED THE FUEL Filter from tank today, the whole goddamn unit is sealed.
so ended up pulling of a plastic cap that has a jet like fitting to enable fuel to go into the pump,poured injector cleaner into filter outlet and flushing it in reverse so compressed air came out of pump inlet-voila whining noise gone. maybe next 35k kms no issues if not new fuel pump assemble is the way to go i recon ,its too much dicking about opening the assembly i guess.
1)remove tank
2)do i have to disconnect anything?fuel lines?any tricks to this?
3)is the filter in the tank or outside? etc
cheers
[/quote]
1 drain fuel from tank
2 remove seat
3 lift tank disconnect fuel line and fuel sender pump wires
4 lower tank unbolt n remove tank from bike,only undo the 2x 12mill bolts to the frame ,leave the 4x 10 mil bolts alone
5 place tank on soft surface upside down ,getallen key undo bolts holding in fuel pump
6 lift sender pump assembly from tank being careful not to bend fuel float
7 remove fitler from pump assembly 8 spray with carby cleaner ,then use compressed air the blow backwards back flush etc while doing this wrap white cloth around fitler as shit will go everywere
8 follow steps in reverse to re-assemble
good luck
[/quote]
REMOVED THE FUEL Filter from tank today, the whole goddamn unit is sealed.could nt see any friggin teabag filter.
so ended up pulling of a plastic cap that has a jet like fitting to enable fuel to go into the pump,poured injector cleaner into filter outlet and flushing it in reverse so compressed air came out of pump inlet-voila whining noise gone. maybe next 35k kms no issues if not new fuel pump assemble is the way to go i recon ,its too much dicking about opening the assembly i guess.
nope actually steps
1)remove tank
2)do i have to disconnect anything?fuel lines?any tricks to this?
3)is the filter in the tank or outside? etc
cheers
[/quote]
1 drain fuel from tank
2 remove seat
3 lift tank disconnect fuel line and fuel sender pump wires
4 lower tank unbolt n remove tank from bike,only undo the 2x 12mill bolts to the frame ,leave the 4x 10 mil bolts alone
5 place tank on soft surface upside down ,getallen key undo bolts holding in fuel pump
6 lift sender pump assembly from tank being careful not to bend fuel float
7 remove fitler from pump assembly 8 spray with carby cleaner ,then use compressed air the blow backwards back flush etc while doing this wrap white cloth around fitler as shit will go everywere
8 follow steps in reverse to re-assemble
good luck
[/quote]
REMOVED THE FUEL Filter from tank today, the whole goddamn unit is sealed.
so ended up pulling of a plastic cap that has a jet like fitting to enable fuel to go into the pump,poured injector cleaner into filter outlet and flushing it in reverse so compressed air came out of pump inlet-voila whining noise gone. maybe next 35k kms no issues if not new fuel pump assemble is the way to go i recon ,its too much dicking about opening the assembly i guess.
Don't tempt fate,TAUNT IT!