Welcome to The Australian Hayabusa Club Forum - ARCHIVE ONLY VERSION - NEW REGISTRATIONS & POSTS DISABLED › Bike Discussions › Hayabusa Gen.II v
Gen II Bent Countershaft

Gen II Bent Countershaft
masterfabr
Guest
 
#20
14-10-2011, 09:55pm
I'm fine. Thank you. I thought that was you and I assume Jet is the jet I am familiar with also. Yes I am using the busa trans for all the primary shifting duties and the 091 is used for reverse and also allows me to select underdrive/1:1/overdrive (second/third/fourth) using weddle custom ratios in the 091. I use a Ramsey RPV chain but the hi-vo is nearly the same. Good to see others doing something similar. Good work with your design also.I like it.
Reply


Messages In This Thread
Gen II Bent Countershaft - by Camel - 25-09-2011, 12:37am
RE: Gen II Bent Countershaft - by puttputt - 07-10-2011, 12:04am
RE: Gen II Bent Countershaft - by Maj - 07-10-2011, 06:27am
RE: Gen II Bent Countershaft - by fasterfaster - 07-10-2011, 06:31am
RE: Gen II Bent Countershaft - by Camel - 08-10-2011, 08:52am
RE: Gen II Bent Countershaft - by Fineline22 - 08-10-2011, 11:37am
RE: Gen II Bent Countershaft - by Fineline22 - 07-10-2011, 04:33pm
RE: Gen II Bent Countershaft - by GRUNTMAX - 07-10-2011, 11:08am
RE: Gen II Bent Countershaft - by Maj - 07-10-2011, 07:09pm
RE: Gen II Bent Countershaft - by Camel - 09-10-2011, 08:21am
RE: Gen II Bent Countershaft - by Aussie Steve - 09-10-2011, 10:20am
RE: Gen II Bent Countershaft - by whitedragon - 09-10-2011, 01:11pm
RE: Gen II Bent Countershaft - by Camel - 09-10-2011, 03:44pm
RE: Gen II Bent Countershaft - by whitedragon - 09-10-2011, 04:29pm
RE: Gen II Bent Countershaft - by Camel - 10-10-2011, 07:04pm
RE: Gen II Bent Countershaft - by masterfabr - 12-10-2011, 10:38am
RE: Gen II Bent Countershaft - by whitedragon - 12-10-2011, 10:57am
RE: Gen II Bent Countershaft - by masterfabr - 12-10-2011, 11:22am
RE: Gen II Bent Countershaft - by Camel - 14-10-2011, 03:49pm
RE: Gen II Bent Countershaft - by masterfabr - 14-10-2011, 09:55pm
RE: Gen II Bent Countershaft - by masterfabr - 18-10-2011, 10:47am
RE: Gen II Bent Countershaft - by whitedragon - 18-10-2011, 06:16pm
RE: Gen II Bent Countershaft - by Camel - 20-10-2011, 03:11pm
RE: Gen II Bent Countershaft - by whitedragon - 20-10-2011, 03:30pm
RE: Gen II Bent Countershaft - by Jet109 - 20-10-2011, 03:52pm
RE: Gen II Bent Countershaft - by Camel - 20-10-2011, 04:41pm
RE: Gen II Bent Countershaft - by masterfabr - 20-10-2011, 10:51pm



Users browsing this thread: 1 Guest(s)