Welcome to The Australian Hayabusa Club Forum - ARCHIVE ONLY VERSION - NEW REGISTRATIONS & POSTS DISABLED › Bike Discussions › Technical Discussion v
Turbo bike part 1 - Brain transplant

Turbo bike part 1 - Brain transplant
1hotBUSA
Guest
 
#35
13-10-2005, 10:38pm
Hi there,

I am going for a water injection system basically on cost and space savings. It's going to get tight in there if I go with the intercooler and a good one is going to cost a mint. I will be switching the water so it comes on over a predetermined boost pressure anyway. Anyway I only have to mod the up pipe if I get hold of an intercooler later on.

Bruce, I am everywhere for the plating at the moment. Got some parts from Chrome Factory in Caringbah....bit far away, the swingarm is in at Astors who seem quite professional but they wont chrome wheels, only nickel them. I was also going to see Swifts at Silverwater. One thing I did like about Aster was that they were able to give me a price straight away rather than muck me around, and they can fit anything, you could plate the frame if it took your fancy. IMHO Electromold are overpriced and i wouldnt bother shipping all the way to the police state to get rorted like that. If you want prices PM me and I will spill. That goes for anybody. Lets Bling them Busas, as long as I get a good supply of groupies. (I'm sure a boost gauge will help that)

Regards
Graham
1hotBUSA
2000 Suzuki Hayabusa Red/Grey Bog standard except for bling and a kanooter valve. Oh and a turbo kit on the floor.
Strike a blow for freedom...Smash a speed camera!!!
Red Bikes Rule!!!!!<i></i>
Reply


Messages In This Thread
Turbo bike part 1 - Brain transplant - by 1hotBUSA - 18-09-2005, 05:57pm
190 Hp - by fasterfaster1 - 18-09-2005, 08:34pm
Re: 190 Hp - by 1hotBUSA - 18-09-2005, 09:49pm
Flow rate - by gazza414 - 18-09-2005, 11:00pm
Re: Flow rate - by the shredder 3 - 18-09-2005, 11:34pm
Re: Flow rate - by gazza414 - 18-09-2005, 11:45pm
Re: Flow rate - by the shredder 3 - 18-09-2005, 11:55pm
Re: Flow rate - by gazza414 - 19-09-2005, 12:14am
Re: Flow rate - by hawkwind racing - 19-09-2005, 05:47pm
Re: Flow rate - by 1hotBUSA - 19-09-2005, 07:16pm
Re: Flow rate - by Maj750t - 19-09-2005, 07:23pm
Re: Flow rate - by 1hotBUSA - 19-09-2005, 07:30pm
Re: Flow rate - by Maj750t - 19-09-2005, 08:28pm
Tsi map - by Blackkat - 19-09-2005, 08:52pm
Re: Injectors - by gazza414 - 19-09-2005, 09:51pm
Re: Injectors - by 1hotBUSA - 19-09-2005, 09:58pm
Re: Injectors - by gazza414 - 19-09-2005, 10:11pm
Re: Injectors - by 1hotBUSA - 19-09-2005, 10:20pm
Re: Injectors - by gazza414 - 19-09-2005, 10:43pm
Re: Injectors - by Maj750t - 19-09-2005, 10:51pm
Re: Injectors - by 1hotBUSA - 20-09-2005, 05:45pm
Re: Injectors - by CAS3234 - 20-09-2005, 06:38pm
Re: Injectors - by gazza414 - 20-09-2005, 10:49pm
Re: Injectors - by CAS3234 - 21-09-2005, 08:41am
Re: Injectors - by gazza414 - 21-09-2005, 11:32am
Re: Injectors - by CAS3234 - 24-09-2005, 09:08am
Injectors - by Blackkat - 24-09-2005, 08:45pm
Re: Injectors - by CAS3234 - 24-09-2005, 11:27pm
Re: Injectors - by 1hotBUSA - 05-10-2005, 07:13pm
Where are you up 2?? - by CAS3234 - 12-10-2005, 08:38pm
Re: Where are you up 2?? - by 1hotBUSA - 13-10-2005, 07:38pm
Re: Where are you up 2?? - by CAS3234 - 13-10-2005, 07:41pm
Re: Where are you up 2?? - by Blackzook - 13-10-2005, 07:41pm
Re: Where are you up 2?? - by simmo - 13-10-2005, 10:13pm
Re: Where are you up 2?? - by 1hotBUSA - 13-10-2005, 10:38pm
Re: Where are you up 2?? - by pan - 14-10-2005, 12:23am
Plater and Anodizers - by gazza414 - 14-10-2005, 07:20am
Re: Plater and Anodizers - by 1hotBUSA - 14-10-2005, 07:21pm
Pan's mirrors - by Blackkat - 14-10-2005, 10:04pm
Re: Pan's mirrors - by pan - 14-10-2005, 11:31pm
Re: Pan's mirrors - by 1hotBUSA - 15-10-2005, 04:27pm
Pan's mirrors - by Blackkat - 15-10-2005, 08:55pm
Re: Pan's mirrors - by Geribusa - 16-10-2005, 04:56am
Re: Pan's mirrors - by Maj750t - 16-10-2005, 09:53pm
Re: Pan's mirrors - by Geribusa - 16-10-2005, 11:57pm
Re: Pan's mirrors - by Maj750t - 17-10-2005, 12:28am
Injector Flow - by gazza414 - 17-10-2005, 12:07pm
Injector Flow - by Blackkat - 17-10-2005, 08:26pm
Re: Injector Flow - by Geribusa - 18-10-2005, 03:46am
Choked Flow - by gazza414 - 18-10-2005, 02:43pm
Re: Choked Flow - by Geribusa - 19-10-2005, 04:11am
Re: Choked Flow - by Maj750t - 19-10-2005, 09:27am
Re: Choked Flow - by 1hotBUSA - 19-10-2005, 07:20pm
Re: Choked Flow - by Geribusa - 20-10-2005, 03:41am
Re: kit??? - by Maj750t - 20-10-2005, 09:58am
Re: kit??? - by 1hotBUSA - 20-10-2005, 08:40pm
Re: kit??? - by Xhiler8r - 20-10-2005, 09:43pm
Re: kit??? - by Geribusa - 21-10-2005, 03:54am
Kudos to you - by fasterfaster1 - 21-10-2005, 07:15am
Re: Kudos to you - by 1hotBUSA - 21-10-2005, 07:09pm
Re: Kudos to you - by Geribusa - 22-10-2005, 03:51am
CAD - by Maj750t - 22-10-2005, 10:14am
Re: CAD - by Geribusa - 22-10-2005, 10:03pm
CAD - by Maj750t - 23-10-2005, 11:04am
Re: CAD - by 1hotBUSA - 23-10-2005, 10:14pm
Re: CAD - by CAS3234 - 20-11-2005, 12:03pm
Re: CAD - by 1hotBUSA - 21-11-2005, 05:16pm
Re: CAD - by Geribusa - 21-11-2005, 08:37pm
Re: CAD - by 1hotBUSA - 22-11-2005, 04:35pm
Re: CAD - by Geribusa - 23-11-2005, 12:51am
Re: CAD - by aBUSa - 21-01-2006, 10:07am
Re: turbo kit prices - by DAN85 - 22-01-2006, 07:48am
Re: turbo kit prices - by Geribusa - 22-01-2006, 08:37am
Re: turbo kit prices - by aBUSa - 22-01-2006, 08:52am
Turbo Kits Fully Imported or Local Kits ! - by fasterfaster1 - 22-01-2006, 02:07pm
Re: Turbo ! - by DAN85 - 22-01-2006, 05:32pm
Reliable as - by aBUSa - 22-01-2006, 08:25pm
Re: Reliable as - by fasterfaster1 - 23-01-2006, 08:41am
Re: Reliable as - by Blackkat - 23-01-2006, 03:50pm



Users browsing this thread: 2 Guest(s)