Fitting Centrestand

[Ward P]

I went to put the centrestand on that I got from Andycad onto my '99. It seemed straight forward, but I can't locate where the springs hook onto the bike, and the stand comes too far forward which leaves the rear wheel on the ground and the bike on an angle with the stand not sitting on the ground right.
I am assuming that I need a new bolt to go right through the stand????? and this seems to be about where I think the 2 springs should go.

Is there a bracket that is needed that I don't have??
Also the flat bit at the top of the stand looks like it should sit flat against something when the stand is down, but buggered if I can see what.

Does anyone have a stand fitted that they could post a couple of close-up photos of ??

cheers,

WARD

[Ward P]

Surely someone has a centre stand . . .

anyone . . .

I know loafie has one!

hello . . .

helloooooooo. . .

is there anybody out thereeeeeeee

[andcad]

Surely someone has a centre stand . . .

anyone . . .

I know loafie has one!

hello . . .

helloooooooo. . .

is there anybody out thereeeeeeee

Found these in my box of bits and pieces, I dont know if you need one or all of them. I will send them over asap for you.

[attachment=2617]

[LOAFIE]

Surely someone has a centre stand . . .

anyone . . .

I know loafie has one!

hello . . .

helloooooooo. . .

is there anybody out thereeeeeeee

Sorry Wardy , i dont have a centre stand. Just a rear race stand . Good luck with your search
I think it was Capebusa with the centre-stand at Jindy and it was a Blue busa

[lindsay busa]

i have a centre stand on my bike i hope this helps

[BUSGO]

There is a guy in Newcastle with a centrestand fitted but he is not on the internet.
I'll see if I can catch up with him if you are still having a prob Ward.

BTW. He got his chromed before fitting it and it looks great!

[BUSGO]

Just had a thought Ward....



The type of busa owner that fits a centrestand is more likely to be found on the ULYSSES website.
You might have better luck over there.

[lindsay busa]

i have photo but can not get the photo to upload

[Ward P]

Just had a thought Ward....



The type of busa owner that fits a centrestand is more likely to be found on the ULYSSES website.
You might have better luck over there.

You are an utter utter utter bastard Ray!

[tomrux]

Page 8_39 in the workshop manual shows all the guts on fitting a center stand. not quite sure why you would want to but there it is



Tom

[BUSGO]

I may be an "UTTER UTTER UTTER BASTARD" Ward.

But have a very anyway mate.


(Now you feel even older - don't you!)
sorry....

[Madmax]

I may be an "UTTER UTTER UTTER BASTARD" Ward.

At least you admit it Ray. Very big of you!


Max

[Ward P]

I may be an "UTTER UTTER UTTER BASTARD" Ward.

But have a very anyway mate.


(Now you feel even older - don't you!)
sorry....

Cheers Mate, thanks very much for reminding me - at least I'm not old enough to be a full Ulyssees member just yet. -just remember, you're only as old as the woman you feel. (unfortunately she's just had her birthday too.)

& thanks Tom for the info. - just what I needed.
With the extras that Andy is sending me I'll be sweet.

Thanks all,

WARD

[Madmax]

I may be an "UTTER UTTER UTTER BASTARD" Ward.

But have a very anyway mate.


(Now you feel even older - don't you!)
sorry....

Cheers Mate, thanks very much for reminding me - at least I'm not old enough to be a full Ulyssees member just yet. -just remember, you're only as old as the woman you feel. (unfortunately she's just had her birthday too.)

& thanks Tom for the info. - just what I needed.
With the extras that Andy is sending me I'll be sweet.

Thanks all,

WARD

To get that bolt in, the instructions advised that you remove the complete exhaust system. When I added a centre stand a few years ago i just loosened the header bolts enough to collapse the pipe far enough just to get that rotten bolt passed the pipe.

Takes a while, good luck.


Max