+- Welcome to The Australian Hayabusa Club Forum - ARCHIVE ONLY VERSION - NEW REGISTRATIONS & POSTS DISABLED (https://www.australian-hayabusa-club.com/MyBB)
+-- Forum: Bike Discussions (https://www.australian-hayabusa-club.com/MyBB/forumdisplay.php?fid=35)
+--- Forum: Hayabusa Gen.II (https://www.australian-hayabusa-club.com/MyBB/forumdisplay.php?fid=45)
+--- Thread: FI LIGHT ON ? (/showthread.php?tid=18621)
FI LIGHT ON ? - beally55 - 13-02-2012
The fi light has come on a couple of times , but if I turn the ignition off and then restart it it goes out .When it is on the bike seems to run ok .Any ideas on what the problem might be?
Only done 13000 kms and had the regulator/rectifier recall done..
Would appreciate any help .
Chris
RE: FI LIGHT ON ? - 99er - 13-02-2012
could be any sensor.did you wash the bike?
RE: FI LIGHT ON ? - beally55 - 13-02-2012
(13-02-2012, 11:42am)99er Wrote: could be any sensor.did you wash the bike?
Washed it about 10 days ago ,. and its just been in the shed.This morning it came on 15 mins into the ride .
I will keep an eye on it , but I am going for a lonbg ride tomorrow and i hope it doesnt die in the middle of nowhere
RE: FI LIGHT ON ? - 99er - 13-02-2012
IF ITS GOOD WEATHER WHERE YOU ARE LEAVE IT OUTSIDE IN THE SUN.WARM THE BIKE UP TO HELP IT DRY OUT,THIS HAPPENED TO ME ON MY GEN 1,
RE: FI LIGHT ON ? - Maj - 13-02-2012
Bridge the dealer plug under the seat
white plug , next to rhs seat retaining loop
its a 6 wire plug with 4 wires
2 of the wires, the white/red and the black white , next to each other on the plug , need joining to put the fault codes on the dash , your actually earthing the white red when you do this, i just strip back a bit of electrical wire and push the ends into the plug , you can leave it in untill you get a fault, doesn't effect anything else , just tape the wires in place
RE: FI LIGHT ON ? - Greeny_SA - 13-02-2012
Maj , will the gen 1 Dealer (toggle switch ) work on gen 2 as I have one Chris can borrow .
RE: FI LIGHT ON ? - beally55 - 13-02-2012
(13-02-2012, 12:16pm)Maj Wrote: Bridge the dealer plug under the seat
white plug , next to rhs seat retaining loop
its a 6 wire plug with 4 wires
2 of the wires, the white/red and the black white , next to each other on the plug , need joining to put the fault codes on the dash , your actually earthing the white red when you do this, i just strip back a bit of electrical wire and push the ends into the plug , you can leave it in untill you get a fault, doesn't effect anything else , just tape the wires in place
Thanks Maj, i`ll try that for my ride tomorrow. I guess by what you are saying that it will do no harm to leave the bridge in all the time.
Geeeny thanks for the offer .Why don`t you come for a ride tomorrow ....the beer taps can wait.The forecast is perfect
(13-02-2012, 12:09pm)99er Wrote: IF ITS GOOD WEATHER WHERE YOU ARE LEAVE IT OUTSIDE IN THE SUN.WARM THE BIKE UP TO HELP IT DRY OUT,THIS HAPPENED TO ME ON MY GEN 1,
I`ll try that first, that is probably all it is.
Thanks
RE: FI LIGHT ON ? - Greeny_SA - 13-02-2012
Love to Chris ,But have some pub's with no beer & they won't wait. Next time Mate ,
RE: FI LIGHT ON ? - Maj - 13-02-2012
The gen 1 is a 4 pin plug but the switch (or any switch) and wires will work , you can de pin the wires and terminals out of the 4 pin plug if you need
RE: FI LIGHT ON ? - ROD - 13-02-2012
(13-02-2012, 12:16pm)Maj Wrote: Bridge the dealer plug under the seat
white plug , next to rhs seat retaining loop
its a 6 wire plug with 4 wires
2 of the wires, the white/red and the black white , next to each other on the plug , need joining to put the fault codes on the dash , your actually earthing the white red when you do this, i just strip back a bit of electrical wire and push the ends into the plug , you can leave it in untill you get a fault, doesn't effect anything else , just tape the wires in place
Thanks for that info Maj i have placed with the codes in tech discusion
Here are codes for you Chris
c00 none
c11 camshaft position sensor
c12 crankshaft positions sensor, pickup coil signal, signal generator
c13 intake air pressure sensor connection
c14 throttle position sensor
c15 engine coolant temp sensor
c17 intake air pressure sensor #1 for cylinder #1
c18 intake air pressure sensor #2 for cylinder #2
c19 intake air pressure sensor #3 for cylinder #3
c20 intake air pressure sensor #4 for cylinder #4
c21 intake air temp sensor
c22 atmospheric pressure sensor
c23 tipover sensor
c24 ignition signal, coil #1 for cylinder #1
c25 ignition signal, coil #2 for cylinder #2
C26 ignition signal, coil #3 for cylinder #3
C27 ignition signal, coil #4 for cylinder #4
c28 secondary throttle valve actuator
c29 secondary throttle position sensor
C30 secondary throttle control unit
c31 gear position sensor
c32 injector signal #1 for rear cylinder
c33 injector signal #2 for front cylinder
c34 injector signal #3
c35 injector signal #4
c40 idle speed control valve
c41 fuel pump control system, fuel pump, fuel pump relay
c42 ignition switch signal, anti theft
c44 heated oxygen sensor
C46 exhaust control valve actuator (01-02 1000 and 06-07 600/750/1000 ONLY)
c49 PAIR control solenoid valve connection
c60 cooling fan relay connection
c62 EVAP system purge control solenoid valve connection (only in California models)
c92 fuel gauge
RE: FI LIGHT ON ? - beally55 - 14-02-2012
Thank
s for the help ,I'll let you know how I get on
RE: FI LIGHT ON ? - Shifu - 14-02-2012
Hope it is not the C55 code - Too much oil on the chain
Chris, if you need any help give me a call mate. I am fully equipped.
Cheers,
RE: FI LIGHT ON ? - Greeny_SA - 14-02-2012
(14-02-2012, 10:10pm)Shifu Wrote: Hope it is not the C55 code - Too much oil on the chain
Chris, if you need any help give me a call mate. I am fully equipped.
Cheers,
Glad your fully equipped Shifu but, can you help with the bike ?
RE: FI LIGHT ON ? - Shifu - 15-02-2012
(14-02-2012, 10:44pm)Greeny_SA Wrote:(14-02-2012, 10:10pm)Shifu Wrote: Hope it is not the C55 code - Too much oil on the chain
Chris, if you need any help give me a call mate. I am fully equipped.
Cheers,
Glad your fully equipped Shifu but, can you help with the bike ?
Sure thing mate.
RE: FI LIGHT ON ? - beally55 - 16-02-2012
(15-02-2012, 10:06am)Shifu Wrote:(14-02-2012, 10:44pm)Greeny_SA Wrote: [quote='Shifu' pid='260898' dateline='1329221429']
Hope it is not the C55 code - Too much oil on the chain
Chris, if you need any help give me a call mate. I am fully equipped.
Cheers,
Glad your fully equipped Shifu but, can you help with the bike ?
Sure thing mate.
[/quote
Andrew, I guess that the c55 code has never come up on your girl
