+- Welcome to The Australian Hayabusa Club Forum - ARCHIVE ONLY VERSION - NEW REGISTRATIONS & POSTS DISABLED (https://www.australian-hayabusa-club.com/MyBB)
+-- Forum: Bike Discussions (https://www.australian-hayabusa-club.com/MyBB/forumdisplay.php?fid=35)
+--- Forum: Technical Discussion (https://www.australian-hayabusa-club.com/MyBB/forumdisplay.php?fid=5)
+--- Thread: Fitting after market Wheels (/showthread.php?tid=18498)
Fitting after market Wheels - ROD - 17-01-2012
OK having a few little problems With my Gen 2 Wheels
The back has no spacers sent with wheels I can chop the little pipe that came with hubs in half to get two 12mm spacers for Back .
Tha front has a tube i can cut two 12mm spacers for front .
But i had a look at stock wheel at front and there is a 12 mm gap with no spacers is this corect what holds the wheel in line (the Brake pads )
RE: Fitting after market Wheels - Maj - 17-01-2012
Rod i think you need to call the supplier , the short spacer look a lot like the one that goes between the drive hub and wheel , and the long one look like it belongs between wheel bearings ,
RE: Fitting after market Wheels - ROD - 17-01-2012
(17-01-2012, 06:40pm)Maj Wrote: Rod i think you need to call the supplier , the short spacer look a lot like the one that goes between the drive hub and wheel , and the long one look like it belongs between wheel bearings ,
Thanks Mag i Think these could of been of the first set of hubs then I have got a little spacer between the drive hub and wheel And both weels have there spacers between the wheel bearings
RE: Fitting after market Wheels - BLACKZOOK - 17-01-2012
Rod there should be a spacer front wheel - check here
http://www.ronayers.com/Fiche/TypeID/26/Type/FRONT_WHEEL_(GSX1300BKAK8_AK9)/MakeID/2/Make/Suzuki/YearID/50/Year/2009/ModelID/8409/Model/GSX1300BK,A/GroupID/403066/Group/FRONT_WHEEL_(GSX1300BKAK8_AK9)
RE: Fitting after market Wheels - ROD - 17-01-2012
(17-01-2012, 09:22pm)BLACKZOOK Wrote: Rod there should be a spacer front wheel - check here
http://www.ronayers.com/Fiche/TypeID/26/Type/FRONT_WHEEL_(GSX1300BKAK8_AK9)/MakeID/2/Make/Suzuki/YearID/50/Year/2009/ModelID/8409/Model/GSX1300BK,A/GroupID/403066/Group/FRONT_WHEEL_(GSX1300BKAK8_AK9)
True i have not put the spacer back in b4 takin photo but once in still 12mm each side
might go and have look at other gen 2 Tommorow 
RE: Fitting after market Wheels - Maj - 18-01-2012
Rod the supplier for those wheels should have a fitting kit specific to your bike
usually spacers, wheelbearings, sometimes sprocket carriers ,
if you get something custom made or modify existing stuff you will need to be very accurate , remember if something goes wrong in that area of the bike it could at best chew out some very expensive wheels and at worst throw you up the road
RE: Fitting after market Wheels - ROD - 18-01-2012
(18-01-2012, 08:22am)Maj Wrote: Rod the supplier for those wheels should have a fitting kit specific to your bike
usually spacers, wheelbearings, sometimes sprocket carriers ,
if you get something custom made or modify existing stuff you will need to be very accurate , remember if something goes wrong in that area of the bike it could at best chew out some very expensive wheels and at worst throw you up the road
Yes thanks Mag i have contacted them to see if i can get spacer Kit.
RE: Fitting after market Wheels - Maj - 18-01-2012
At least you have current model stuff and should be readily available
My 5 spoke Marchinese wheels (99 vintage)are no longer supported and i need a fitting kit
RE: Fitting after market Wheels - ROD - 18-01-2012
Contacted suplier front i use stock set up and have to wait for rear to be sent out .
I fited front wheel and put a guage over each side at 4 diferent points and got same all 4 times so happy with that
So had time to spare and gen 1 looked lonely so gave her wheels a new make over
RE: Fitting after market Wheels - simmo - 18-01-2012
Do I know those Gen 1 wheels
What are the Gen 2 ones
better pic please 
RE: Fitting after market Wheels - ROD - 18-01-2012
(18-01-2012, 04:28pm)simmo Wrote: Do I know those Gen 1 wheels
What are the Gen 2 ones
Yes found them under some old copper
Gen 2 wheels rccomponents Havocs
Dont tell Max im trying to whip his But at Tathra
RE: Fitting after market Wheels - Shifu - 19-01-2012
They resemble a meat slicer. Can be handy for a BBQ
RE: Fitting after market Wheels - simmo - 19-01-2012
(18-01-2012, 07:04pm)ROD Wrote:(18-01-2012, 04:28pm)simmo Wrote: Do I know those Gen 1 wheelsYes found them under some old copper
What are the Gen 2 ones
Gen 2 wheels rccomponents Havocs
Dont tell Max im trying to whip his But at Tathra
Whip him or cut him up
, you could do his other need operation for with them don't stick your hand in them while they are spinning RE: Fitting after market Wheels - BEAU - 19-01-2012
(18-01-2012, 04:21pm)ROD Wrote: Contacted suplier front i use stock set up and have to wait for rear to be sent out .
I fited front wheel and put a guage over each side at 4 diferent points and got same all 4 times so happy with that
So had time to spare and gen 1 looked lonely so gave her wheels a new make over
What are the brand of wavey disks you had on the Genl Rod? Do you want to sell them? I'm after some for my 14.
Cheers, Beau.